Results 1 to 8 of 8
  1. #1
    scorpiusdeus's Avatar
    scorpiusdeus is offline Supporting Member
    Join Date
    Feb 2007
    Ventura County, CA

    Replacing/installing a trigger

    I have a Sig armorers DVD, but i haven't watched it yet. I'm wondering if any of you have replaced or installed a new trigger in a P239 or P226 series and how difficult was it? Any idiosyncrasies or things I might need to know before I begin?

  2. #2
    Vom Kriege's Avatar
    Vom Kriege is offline Member
    Join Date
    May 2006
    I can't answer your question, but I will follow this thread as I am interested in getting an older Sig and putting in the SRT system.

  3. #3
    Spenser is offline Member
    Join Date
    Nov 2006
    If you figure it out, let us know about it. There's a 229 I know that needs a serious trigger job....

  4. #4
    SigZagger's Avatar
    SigZagger is offline Member
    Join Date
    Aug 2006
    I would assume the DVD addresses that procedure. I read (can't remember where) that the Sigsauer factory is going to offer the SRT as an aftermarket update. I'll consider it for my 229.

  5. #5
    Firebird is offline Junior Member
    Join Date
    Feb 2008
    I am new to sigs, I own a p226. What does SRT mean?

  6. #6
    Ram Rod's Avatar
    Ram Rod is offline Senior Member
    Join Date
    Jan 2008
    Washington county, arkansas
    Short reset trigger. Interesting concept, but it's not available for my P220 SAO. The curve is designed a bit differently and doesn't end up going as forward to reset in essence as the regular stock trigger. I think this is mainly for the DA/SA models. My SAO will actually reset like my Glock pistols once you learn where it is and not to completely let go of the trigger. The SRT's are already available and from SIG as well as other suppliers. There is also a 'short trigger' for those with smaller hands. The trigger however will still need to travel as far forward as the stock in order to reset. SIG custom shop will do this for $99.95
    Last edited by Ram Rod; 02-13-2008 at 05:05 PM.

  7. #7
    yetchtoo is offline Junior Member
    Join Date
    Aug 2007

    Sig trigger replacement

    I would watch the video first. I have replaced the original trigger for a short trigger on my new P229ST Elite, and also completely disassembled, cleaned, replaced a hammer spring, and reassembled a cherry P6 that I have. It is pretty straight-foreward.

  8. #8
    SaltyDog's Avatar
    SaltyDog is offline Member
    Join Date
    Jan 2009
    I put a short trigger in my P229 DAK and it was pretty simple. I did a Google search and found a step by step instruction for changing it out.

    The only problem I ran in to were the instructions said to remove the left handgrip to access and remove the trigger bar spring. Actually it is under the right handgrip if you are looking from the back of the pistol and left if you are looking down the barrel. A matter of perspective I guess.

    Also I had a slight problem aligning the Locking Insert on to the Trigger Pivot Pin but once I got it in there I understood what they were referring to.

    I didn't have any extra parts left either

Remove Ads


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Search tags for this page

how to change the trigger in a p239
how to change trigger on sig p226
how to replace a trigger in a p226
replace triger for p226
sig 226 hammerspring replace
sig p220 trigger install
sig sauer p229 srt change out
sig sauer p239 disassembly for srt trigger install
sig sauer p239 disassembly for srt trigger install tool

sig srt installation

trigger rplacement on sig 229
youtube video on how to remove the trigger on a 229 sig handgun
Click on a term to search for related topics.

» Springfield Armory

» HGF Sponsors

Powered by vBadvanced CMPS v4.3.0