Anybody's P380 slide lock shut?? (range report too)
Hi all -not here to bash Kahr in ANY way, I LOVE my PW9 but I have a couple questions on my new P380 - above the usual break-in process. Here goes:
Out of the box: Tore it down, cleaned it, and lubed it.
Loaded (1) round in the mag, shot it; loaded (2) in the mag, shot it. Needed some help closing the slide on the second round, but not bad.
Ran the following types & quantities of ammo through it to break it in:
- (200) WWB 95 gr FMJ
- (200) MagTech 95 gr FMC
- (50) Win 95 gr T-Series Rangers
- (50) Fiocchi 95 gr HP
- Great machining; finish, and appearance
- Absolutely serves the purpose for which it was made - a deep carry or BUG in the pocket.
- I can get (2) firm fingers on the grip when firing, which led to . . .
- Very controllable and minimal felt recoil. I tell you - I've heard some horror stories on some 380's - this one is fine. (500) pain-free rounds in one session.
- Pretty good sights - especially for a small pistol like this.
- Shot low-left: 2" down and left at 7 yards.
- Slide locked shut after (500) rounds.
- Pricey for a pocket gun, but I'm a firm believer in Kahr. My 9 is a GREAT pistol.
Expected: New-Kahr-pistol unbroken in jams.
I listed the ammo in the order of feeding - good to bad. After 2 full mags, the WWB & MagTech fed pretty well - not pefect, but well for that quantity. The SD ammo will be a challenge for abit yet I think. It took nearly all (50) Rangers to start to cycle OK; still not ready for a CCW with them yet. The Fiocchi's were horrible. It was truly painful getting those down the tube. It looked to me that their truncated-like HP cone design made them too long?
Of the misfeeds, except for the Fiocchi, they all started to go into the chamber, but the rims of the cartridges were getting hung-up on the extended (!?!) firing pin. I'd have to drop the mag, jiggle the slide/push the roung out with my finger, and then reload. No tap-rack-and slap fixed these. VERY painful - if 2 mags worth went through fine, it was a miracle.
The firing pin was free to move back and forth and I didn't get any slam-fires, but I found it very odd that the rim of the cartridge was catching it.
The firing pin jam would happen every 3rd or so mag for the first couple-hundred rounds I shot, got a little better, but still there. It maybe happened once or twice in the last 50.
Then - I got home and went to clean it. I couldn't pull the slide back more than a 1/16th of an inch; it was LOCKED. The slide lock was seated properly. I could tell it wasn't loaded from the position of the extractor so I pulled the trigger and it was still tough, but I could open the slide then. I couldn't see anything hanging-up or blocking it from looking at the frame. I closed it - same thing. Had to pull the trigger to get the slide to move. Tried this 6 times.
It didn't matter if a mag was in or not and I tried 3 different mags - same result.
I took the slide off and the pistol was really DIRTY inside! I cleaned it like crazy, lubed it, and closed the slide - it locked again! :smt120 I pulled back fairly hard on the slide and it did open - after it had a slight "catch" on something and locked open. After that - so far it's been fine. Of course, I haven't shot it again after the cleaning.
I'm going to call Kahr Tuesday and ask about the firing pin, slide, and low left POI.
Has anyone else experienced any of these anomalies? I did search here and on the 'net and didn't find either of the mechanical issues I experienced.
The POI issue - I'm surprised; my PW9 is right on and even at 15 to 20 yards it prints better groups than I would expect out of that short barrel.
Whaddya folks think? Sounds like my P380 is going on a little trip to the doc's?