Results 1 to 10 of 10
  1. #1
    AZ Outlaws's Avatar
    AZ Outlaws is offline Member
    Join Date
    Dec 2007
    Location
    Mesa, AZ
    Posts
    213

    Question Barrel Nicks....

    These nicks can't be normal???

    Here are two pictures of the barrel from my Sig Sauer P226 Elite .40S&W which has about 400 rounds
    down range. The pics are enlarged to better show the nicks. They are deep enough so when you
    run your fingernail across the top of barrel, you can easily feel them.

    I'm thinking my P226 needs to take a trip back to the factory, what does everyone think?

    Thanks for your opinions and comments....

    The top of barrel showing the location of the nicks....



    A closeup of the nicks....


  2. #2
    DJ Niner's Avatar
    DJ Niner is offline HGF Forum Moderator
    Join Date
    Oct 2006
    Location
    North-Central USA
    Posts
    4,467
    I'd agree that a factory inspection might be a good idea.

    This may be a silly question, but did you happen to look at this area prior to shooting the weapon, or only after it had been fired? I'm just wondering if they were there all along (factory defect, perhaps), or if they developed during the course of shooting.

  3. #3
    AZ Outlaws's Avatar
    AZ Outlaws is offline Member
    Join Date
    Dec 2007
    Location
    Mesa, AZ
    Posts
    213
    The pistol has been cleaned and inspected after every trip to the range. I noticed the nicks after yesteday's trip. The entire barrel has shown more and more wear as more ammo has been fired through it....

  4. #4
    Shipwreck's Avatar
    Shipwreck is offline HGF Forum Moderator
    Join Date
    Jan 2006
    Location
    Beretta City, Texas
    Posts
    10,951
    U need that looked at by the factory - I've never had that before...

  5. #5
    Baldy's Avatar
    Baldy is offline Senior Member
    Join Date
    Jun 2006
    Location
    Port St.John,FL.
    Posts
    6,740
    Yes by all means send that back to Sig. Something is out of wack in the timing on that pistol. Good luck.

  6. #6
    AZ Outlaws's Avatar
    AZ Outlaws is offline Member
    Join Date
    Dec 2007
    Location
    Mesa, AZ
    Posts
    213
    Thanks for the replies. I just got back from sending the P226 back to Sig. Bummer, who would of thought I'd have to send it in for repair after only 400 rounds?


    I'm not having any luck at all with guns. I bought a S&W M&40 early Nov. It started dropping the mag at 30 rounds. It went back to S&W, took one month to get it back. While the M&P was gone I turned around a few days later and bought the Sig with the intention of selling the M&P back to the gun shop and apply the refund to the cost of the Sig, but I ended up keeping the M&P.

    Now my wife is worried and said, "when I send guns back I turn around and buy another one right away". She knows I've been looking at 1911's... S&W, Springfield, Sig and Taurus. I also want to get a .44 Charter Arms Bulldog Pug. Hmmmmmmmmm... a trip to the gun shop might just be what the doctor perscribed for me feeling bad about having to send the Sig back....

  7. #7
    AZ Outlaws's Avatar
    AZ Outlaws is offline Member
    Join Date
    Dec 2007
    Location
    Mesa, AZ
    Posts
    213
    Great customer service from Sig!!! Exactly 1 week turn around. I sent my P226 back
    to the factory with a prepaid UPS label on a Friday. It was back in my hands the following
    Friday with a new barrel and new sights. No explanation on what caused the barrel nicks,
    even after a callto the CS rep, Jason and him talking to the smith that looked at the gun.
    We'll see how the new barrel holds up this time.

    And yes, while the P226 was gone I made that trip to the gun shop and traded the M&P40
    for a Springfield 1911 PX9151LP Loaded.

    All is well again!!!


  8. #8
    Shipwreck's Avatar
    Shipwreck is offline HGF Forum Moderator
    Join Date
    Jan 2006
    Location
    Beretta City, Texas
    Posts
    10,951
    Nice 1911!

  9. #9
    Baldy's Avatar
    Baldy is offline Senior Member
    Join Date
    Jun 2006
    Location
    Port St.John,FL.
    Posts
    6,740

    Talking

    Quote Originally Posted by AZ Outlaws View Post
    Great customer service from Sig!!! Exactly 1 week turn around. I sent my P226 back
    to the factory with a prepaid UPS label on a Friday. It was back in my hands the following
    Friday with a new barrel and new sights. No explanation on what caused the barrel nicks,
    even after a callto the CS rep, Jason and him talking to the smith that looked at the gun.
    We'll see how the new barrel holds up this time.

    And yes, while the P226 was gone I made that trip to the gun shop and traded the M&P40
    for a Springfield 1911 PX9151LP Loaded.

    All is well again!!!

    Very good choice here Mr AZ Outlaws. Now get a couple hundred WWB and give us a report of what you think of that Springer. Bet you'll like it as they are a fine pistol. I sure would like to have one in my stable but I got two S&W's and that's enought (naw just kidding). There' never enought when it come to guns. Good luck with yours.

  10. #10
    DJ Niner's Avatar
    DJ Niner is offline HGF Forum Moderator
    Join Date
    Oct 2006
    Location
    North-Central USA
    Posts
    4,467
    That's a great turnaround time from SIG.

    Hope you have better luck from here on out!

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Search tags for this page

1911 knicks on barrel
,
how to repair nicks on beretta o/u barrels
,
knicks in shotgun barrel bad
,
new sig p226 knicks on barrel
,

nicks in the barrel

,
nicks on new sig from factory
,
nicks on the barrel of my new sig 227 pistol
,
niks in agun barrel
,
pistol barrel has nicks
,
sig barrel nicks
,
sig p226 nicks on barrel
,
wear on new sig sauer p226 barrel
Click on a term to search for related topics.

» Springfield Armory

» HGF Sponsors

Powered by vBadvanced CMPS v4.2.1