The reason I bought my 1911 was the weapon's ability to be modified to suit the owner.
The first rule I broke, is buying an extended slide release for my full size.
I know some of the old guys are rolling on the floor about now :smt082
as no one recommends that modification for a CCW gun.
But what I did is to buy a very quality piece from John Masen. The slide release was not very wide and was conctructed with a lot of metal. I must admit it took a lot of "tunning" to get the piece to function properly. The first hurdle to get over was the angle of the piece inside the frame that activates the magazine lock back on the last round. It must not prevent the bullets from loading smoothly into the chamber. Here is where a pack of A-zoom Snap Caps is invaluable. Most of us know that the bullet will strike this part of the slide release "ever so slightly" in most guns.
Next was to counter the extra weight of the extended release, that might cause an un-wanted lock back of the magazine at the wrong time. This was corrected by an old trick of boring a small "detent" in the surface that contacts the Slide stop plunger rod. All this requires is very careful measuring and a good Dremil with diamond bit. The steel of this extended release was VERY hard.
After this work was done - a trip to the range to test the modification.
Firing the 1911 as fast as I could pull the trigger - the slide release worked beautifully. 50 rounds of Blazer Hardball........... flew through the weapon without a pause. The Slide locked back on the last round every time. That's why care must be taken while boring your "Detent" ..... if you make it too deep, the magazine spring won't be able to over come the drag.
Why make this modification in the first place ............... well, under extreme stress have you ever tried to hit those tiny slide release latches ?? At the range, shooting for speed I have missed the release several times. I tried to use the "Rack the slide" method of reloading the gun.......... but that is painfully slow and a lot of times my hand would slip on the slide. This extended slide release is just what the doctor ordered - at least in my case - YMMV !! If you buy the right part [ Wilson Combat makes a nice Tactical extended release ] it is possible to modify the 1911 and not have any problems with the draw from a holster. I don't shoot with thumbs forward, so I don't have to worry about accidental activation of the extended release. While this might not work for many -- it is possible to have it work successfully if care is taken in the install.
JF.
The first rule I broke, is buying an extended slide release for my full size.
I know some of the old guys are rolling on the floor about now :smt082
as no one recommends that modification for a CCW gun.
But what I did is to buy a very quality piece from John Masen. The slide release was not very wide and was conctructed with a lot of metal. I must admit it took a lot of "tunning" to get the piece to function properly. The first hurdle to get over was the angle of the piece inside the frame that activates the magazine lock back on the last round. It must not prevent the bullets from loading smoothly into the chamber. Here is where a pack of A-zoom Snap Caps is invaluable. Most of us know that the bullet will strike this part of the slide release "ever so slightly" in most guns.
Next was to counter the extra weight of the extended release, that might cause an un-wanted lock back of the magazine at the wrong time. This was corrected by an old trick of boring a small "detent" in the surface that contacts the Slide stop plunger rod. All this requires is very careful measuring and a good Dremil with diamond bit. The steel of this extended release was VERY hard.
After this work was done - a trip to the range to test the modification.
Firing the 1911 as fast as I could pull the trigger - the slide release worked beautifully. 50 rounds of Blazer Hardball........... flew through the weapon without a pause. The Slide locked back on the last round every time. That's why care must be taken while boring your "Detent" ..... if you make it too deep, the magazine spring won't be able to over come the drag.
Why make this modification in the first place ............... well, under extreme stress have you ever tried to hit those tiny slide release latches ?? At the range, shooting for speed I have missed the release several times. I tried to use the "Rack the slide" method of reloading the gun.......... but that is painfully slow and a lot of times my hand would slip on the slide. This extended slide release is just what the doctor ordered - at least in my case - YMMV !! If you buy the right part [ Wilson Combat makes a nice Tactical extended release ] it is possible to modify the 1911 and not have any problems with the draw from a holster. I don't shoot with thumbs forward, so I don't have to worry about accidental activation of the extended release. While this might not work for many -- it is possible to have it work successfully if care is taken in the install.
JF.