First i am new to the forum shouldn't be given my desire to shoot. So thanks in advance and I am looking forwards to this forum.
I have a Colt Anaconda revolver in 44 mag
every 5 or more shots it misfires by that I mean the firing pin puts a divot in the primer but its not deep enough to set it off. After comparing the dimple left by the firing pin it is not hitting deep enough in comparison to my other revolvers. It is the same on on shots fired I just think the ones that do fire were only because its just barely off enough that some will not fire.
I bought it used a few months ago and I think it was sold because of this. I have a couple of thoughts on it as well. First i suspect someone has put a new hammer in it and or possibly done some trigger work as its trigger pull is probably in the 2 to 2.5 pound range. There is also some color differences between the trigger and hammer. I shoot a variety of hand guns while I haven't put it on an actual scale I can tell you its trigger pull is light. I like it and its not so light its dangerous but I am sure someones done something to it.
With that being said heres what I know and what I think. The firing pin if pushed in manually with a pick does move freely and deep enough into the cylinder that I do not think it a worn firing pin or an issue with the firing pin?? But I could be wrong the end that the hammer works on may be worn??
Next could the main spring for the hammer be weak not triggering the hammer with enough force this might also reduce trigger pull again a thought but I do not know. I have tried to find a new spring on line but have yet to find someone with one in stock and we no longer have any dealers within 60 miles of here to order one through.
next is the hammer I suspect its been replaced at some point and wonder if the hammer has to be fitted to the gun. The main part of the hammer on it upper edge hits the guns main frame this leaves a gap in the lower area to hit the plate that actually forces the firing pin into the cylinder. The gap between this area and the plate is a lot more on this gun than my other revolvers with similar design. So one of my thoughts is the hammer needs filed down a little to allow the hammerto hit the plate against the firing pin with a little more force. But once again I do not know.
I am pretty crafty and am capable of a spring install if that is a place to start but do not want to start filing on its hammer unless I had a clearance spec or at least an idea of what is right.
Last resort I will drive it in to a gun shop and see if they can help.
Thanks again.
I have a Colt Anaconda revolver in 44 mag
every 5 or more shots it misfires by that I mean the firing pin puts a divot in the primer but its not deep enough to set it off. After comparing the dimple left by the firing pin it is not hitting deep enough in comparison to my other revolvers. It is the same on on shots fired I just think the ones that do fire were only because its just barely off enough that some will not fire.
I bought it used a few months ago and I think it was sold because of this. I have a couple of thoughts on it as well. First i suspect someone has put a new hammer in it and or possibly done some trigger work as its trigger pull is probably in the 2 to 2.5 pound range. There is also some color differences between the trigger and hammer. I shoot a variety of hand guns while I haven't put it on an actual scale I can tell you its trigger pull is light. I like it and its not so light its dangerous but I am sure someones done something to it.
With that being said heres what I know and what I think. The firing pin if pushed in manually with a pick does move freely and deep enough into the cylinder that I do not think it a worn firing pin or an issue with the firing pin?? But I could be wrong the end that the hammer works on may be worn??
Next could the main spring for the hammer be weak not triggering the hammer with enough force this might also reduce trigger pull again a thought but I do not know. I have tried to find a new spring on line but have yet to find someone with one in stock and we no longer have any dealers within 60 miles of here to order one through.
next is the hammer I suspect its been replaced at some point and wonder if the hammer has to be fitted to the gun. The main part of the hammer on it upper edge hits the guns main frame this leaves a gap in the lower area to hit the plate that actually forces the firing pin into the cylinder. The gap between this area and the plate is a lot more on this gun than my other revolvers with similar design. So one of my thoughts is the hammer needs filed down a little to allow the hammerto hit the plate against the firing pin with a little more force. But once again I do not know.
I am pretty crafty and am capable of a spring install if that is a place to start but do not want to start filing on its hammer unless I had a clearance spec or at least an idea of what is right.
Last resort I will drive it in to a gun shop and see if they can help.
Thanks again.