Results 1 to 7 of 7

Thread: 1911-a1

  1. #1
    AC_USMC 03 is offline Junior Member
    Join Date
    Apr 2009
    Posts
    85

    1911-a1

    Well just got the GI and i want to replace the spur,put a beavertail on (I think I do) and a new trigger. Sights are pretty small but i am not sure which sights can be put on this gun. Any help on parts (name brands, which to use or not use) would be appreciated as this is my first 1911 and first "drop in" mods I will be doing.
    Thanks
    Aaron

  2. #2
    DevilsJohnson is offline Senior Member
    Join Date
    Oct 2007
    Location
    Kentucky
    Posts
    3,373
    The Chip McCormick drop ins are really good. Match grade parts and little or no fitting for as price that you can easily afford. Any parts from Fusion are great too.

    in my Springer the hammer and grip safety are chips. I can't remember where I got the barrel bushing. As to sights it depends what you are wanting ot do. Just remember if you get any type of night sights or anything with a novac sight look you will have ot have the slide ground down to fit it. Same with a Mil- Spec. I chose to just use a better front site and left the rear alone on my mil-spec. I didn't want to cut it and change the original design. I have others that are set up for the other sights anyway

  3. #3
    AC_USMC 03 is offline Junior Member
    Join Date
    Apr 2009
    Posts
    85
    here are some parts I have found that i was thinking of using. From www.2rco.com 3 dot dove tail sights $26.25, Wide gripe safety$31.00, from wilsoncombat.com value line skeletonized hammer $29.95 and a comp match trigger $16.95. IS there anything esle I would need for these "Drop In" parts? I know the wilson parts are good to go but what about the www.2rco.com's? Any other better parts out there then these I have found? Like I said I am a noob at this stuff lol

  4. #4
    DevilsJohnson is offline Senior Member
    Join Date
    Oct 2007
    Location
    Kentucky
    Posts
    3,373
    They look OK. I've not used them though. I've pretty much stuck with Wilson, Chip McCormick, Cylinder & Slide, and Fusion. I can ask around though or maybe someone here has more history with them. But they look fine.

  5. #5
    AC_USMC 03 is offline Junior Member
    Join Date
    Apr 2009
    Posts
    85
    for the sights they have to be dove tail correct?

  6. #6
    DevilsJohnson is offline Senior Member
    Join Date
    Oct 2007
    Location
    Kentucky
    Posts
    3,373
    Yeah but if they are longer like a Novak sight then the rounded top of the slide would have to be ground flat. Clark Custom used to make a high profile sight that would go on top without having to flatten the top but I have not seen them in a while so I don't know if they still have them.

    The rear sight is not the bad part of the GI sight really though. you might be able to do something with the front and be able see better. It's a tenon mounded sight but it's not real hard to replace. You might want a gunsmith to look at it but it's not impossible to do yourself either.

  7. #7
    GURU1911 is offline Member
    Join Date
    Nov 2010
    Location
    SEALY, TX.
    Posts
    126

    1911a1 parts advisory

    Here are the parts i have installed on many 1911's since the early 1990's. They have all been of high quality, easy to install with competent gunsmithiig skills:

    1. Nm barrel bushings: Fred kart / gil hebard
    2. Nm trigger: Greider
    3. Fixed sights front & rear: Novak lo-mount
    4. Sear spring: Clark-4 finger
    5. Other springs: Wolff
    6. Hammer, sear, & disconnector: Gil hebard "master class" brand
    7. Frame pins: Gil hebard "master class" or brownells
    8. Grip screw bushings & hex grip screws: Gil hebard / brownells
    9. Metal refinishing: Robar "np3" or "rogard"
    10. Magazine catch button: Greider

    hope these suggested will help you.

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Search tags for this page

1911a1 gunsmithing
,
burwell gunsmithing 1911a1
,
gil hebard 1911 hammer
,
gunsmithing 1911a1
,

master class 1911 parts

,
parts for a 1911 aster
,
replace a trigger on a 1911a1
,
what better sights can be put on a 1911a1
,
wilson combat master grade
Click on a term to search for related topics.